Live Well Control Lever – What Does Right Look Like?

Having problems figuring out what the proper configuration of my live well control lever should look like. I suspect the correct config has "vibrated" to a situation where I can no longer close the live well after filling. I suspect nothing is broken, but just needs to be returned to the proper config, but I dont know what "Right Looks Like"....... Appreciate any feedback or advice.Thanks,SteveLast edited by Sscottfitz on October 29th, 2015, 8:23 pm, edited 1 time in total.

This topic has 9 replies, 5 voices, and was last updated 9 years, 6 months ago by 1stinLA.

Viewing 9 posts - 1 through 9 (of 9 total)

Author

Posts
October 29, 2015 at 8:27 pm #280382

MeanV2
Participant

The cable fastens in the U area of the brass looking bracket. You cant figure it out I will try to get you a picture.Dan

October 29, 2015 at 8:42 pm #280383

Sscottfitz
Participant

Thanks Dan – based on what you see, are all the parts there and I just need to reconfigure it inside the “u” or does it appear I have any broken parts….? The part I cant figure out is the black “nipple” closest to where the cable connects to the lever.

October 29, 2015 at 9:45 pm #280384

MeanV2
Participant

Scott looks like the plastic piece closest to the cable to lever connection is broke off from the threaded section. It is all just plastic on mine and looks the same on yours.Dan

October 29, 2015 at 10:23 pm #280385

Sscottfitz
Participant

Thanks Dan – I was afraid that might be the case – Im almost thinking a better fix would be to get another brass nut to place on the other side (lever side) of the thread to secure the cable sleeve ti the U bracket……

October 30, 2015 at 12:35 am #280386

Swimrunbike
Participant

call the marine department at FlowRite, they will certainly help you out with everything needed

October 30, 2015 at 2:06 am #280387

1stinLA
Participant

I just replaced mine as it broke in the same place when some acorns got in the bilge and jammed the valve. I tried repairing it with another nut, but the plastic threads alone were not strong enough and it broke again. Just get a new cable and save yourself some grief.http://www.basscatstore.com/controlvalveactuator.aspx

October 30, 2015 at 11:03 am #280388

Bass Cat Boats
Keymaster

1stinLA wrote:I just replaced mine as it broke in the same place when some acorns got in the bilge and jammed the valve. I tried repairing it with another nut, but the plastic threads alone were not strong enough and it broke again. Just get a new cable and save yourself some grief.http://www.basscatstore.com/controlvalveactuator.aspxI Agree but wonder why that piece is made out of plastic to begin with and not brass or Stainless. A lot of these problems could be avoided with a little beefing up. I have one that needs replaced as well but with a rotator cuff problem and still in physical therapy I am not sure it is something I can handle. I wish it just had a plug.Dan

October 31, 2015 at 12:37 am #280389

Bass Cat Boats
Keymaster

That has already been pushed to find a thinset nut to replace the plastic part. That is the FlowRite design however.

October 31, 2015 at 2:22 am #280390

1stinLA
Participant

I could not complain as mine was only 14 years old when it broke, and while getting down into the bilge to get the other end loose I found some items that needed some attention on the pumps and hoses.
Author

Posts

Viewing 9 posts - 1 through 9 (of 9 total)

You must be logged in to reply to this topic. Login Register